Jump to content
Diode Dynamics

2003-2004 SVT Cobra Fog Light LED Bulbs! Plug & Play install! See Comparison Photos!

Recommended Posts

blue1_600x115.gif



 

SVT Cobra Fog Light LED Bulbs


Fog_LED_Collage.jpg
 

Fog Light LEDs for 2003-2004 Ford SVT Cobra (pair)

 

We carry LED bulbs for replacement of your Termi's fog lights in all major sizes. This will make your fog lights a nice bright white, without the hassle of HIDs! Just simple plug and play, replace the bulb and you are good to go!

 

We carry the brightest, highest-quality bulbs at the lowest prices. Your order will ship same day, and we're here if you need us for support and service. And we do not raise prices to astronomical levels- We're breaking that market trend, and offering you great, low prices, every day.

 

These LED bulbs are designed by us here in St. Louis, and every bulb carries with it a three-year limited warranty.

 

We also offer three bulb model options:

HP48: 265 lumens. Lower brightness than factory, but still provides the crisp white, modern color of LEDs.
XP80: 510 lumens. Similar brightness to factory.
XML2:1420 lumens. Much brighter than factory. These are bright!

 

*XML2 Available in Yellow (3000K) / Natural White (4300K) / Pure White (5000K) / Cool White (6000K)


Bulb Design:

 

HP48: This bulb is designed with 48 Epistar 3014 LED chips. Thanks to the cap on the top, the light from this High Power Bulb is shined backwards and away from the bulb, not straight out. This means the output is excellent, because it uses the vehicle's housing completely, which then shines the light much more uniformly.

 

XP80: Each of the four sides of this bulb contains three 5W-rated chips, and the top is fitted with four more, under a projector lens. This is the brightest self-contained automotive LED bulb on the market, and is housed in an aluminum casing with a textured finish for maximum heatsinking properties.

 

XML2: Two opposing genuine CREE XM-L2 chips, driven at high power by self-contained regulator unit, in an attractive cast-aluminum housing. Fully waterproof, non-polar, modular design. 

 

2003-MUSTANG-COBRA_wm.jpg


 

 

These bulbs are made up of a quality plastic connector to slide right into the plug, as well as high durability terminals. A load resistor is embedded to prevent blowing the LEDs from voltage surge, and a diode is implanted to protect the LEDs from reverse polarity. The LED is wired for 12V operation, the kind found on all vehicles.

 

Included in your order is TWO BULBS (to fit your Cobra).

 

All of our products come with a 30-day satisfaction guarantee and a 3-year limited warranty.


Fog Light LEDs for 2003-2004 Ford SVT Cobra (pair)

 

***We have bulbs for all SVT Cobra years!!!***

 

Any questions, feel free to ask via email (contact@diodedynamics.com), Post, PM or call: (314) 205-3033

 

*PM us for the free-shipping code* (U.S. forum members only)

 

Thanks,
Nick C.
Diode Dynamics

Edited by Diode Dynamics

Share this post


Link to post
Share on other sites

Here's an output shot with XML2 installed:

 

FORD_Cobra_2003_FOG_h10_xml2_w.jpg

 

Thanks!

Nick C.

Share this post


Link to post
Share on other sites

Here's another shot with the 5000K XML2 installed:

 

clint_lmr_5k_xml2.jpg

 

Nick C.

Share this post


Link to post
Share on other sites

Do you make the XML2 bulb to fit in place of the 880 bulbs? 

I'm looking to replace the bulbs in my fog lights.  I currently have HIDs in them but one of the ballasts have gone bad.  So I'm thinking of getting rid of them altogether.

Share this post


Link to post
Share on other sites
1 hour ago, RedTwilight said:

Do you make the XML2 bulb to fit in place of the 880 bulbs? 

I'm looking to replace the bulbs in my fog lights.  I currently have HIDs in them but one of the ballasts have gone bad.  So I'm thinking of getting rid of them altogether.

 

Unfortunately, the 880/881 bulb size is too small for the higher-powered LED units like the XP80 and XML2. There's just not enough room on the base of that bulb for adequate heat sink.

 

We offer a reliable LED replacement, but it's more for cosmetic purposes. If you are looking for more usable output, a 35 watt HID conversion kit is definitely the way to go.

 

Feel free to give us a call if you have any additional questions: (314) 205-3033

 

Thanks!

Nick C.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.

×