Jump to content

Recommended Posts

My FAST throttle body came in and I couldn’t throw it on fast enough.

32AB558F-A551-4A4F-81B5-71763B895D7C.jpeg
 

24186572-A7D4-4CD0-95B7-21FD43398B3A.jpeg


Looks like I’ll have to mill one corner down to clear the coolant line.

1C28F7C3-35F9-4324-BE1D-04193663EB7B.jpeg

At first I didn’t think it would work at all due to this large opening but realized it was a blind hole. What a relief, I was ready to go riot.

761923E3-F2F9-4238-BA6D-2CBB6A1E260A.jpeg

A11882B7-CDA3-4606-ABA2-7E47F39C237F.jpeg

The fit will still be very tight due to the upward cant but look how much space I was able to save!

326714EC-05FD-4D2F-8C89-B1A27715076E.jpeg

6BAB751F-5D58-4789-A4B8-F86A2BE6EC83.jpeg

Overall, I’m happy with it and I like the powder coated black housing over the polished Accufab.
 

CB82985E-A854-4352-A193-C787BFA3326F.jpeg

Link to post
Share on other sites

Oh boy..

 

D4921793-5D9A-497C-B712-10D85E5431AC.jpeg

 

I’m going to make this happen, just going to take a little geometry and a few curse words.

 

9135860C-99DA-4BCE-BF85-C0786700767C.jpeg

 

DBCD9E37-79B7-408E-A1FD-2F5B064C344A.jpeg

 

 

Link to post
Share on other sites

I have two wires to lengthen and then the car side of the Holley is installed!

(Again)

After that, I’ll have to change a few sensor connectors out under the hood and the rest is “plug and play”!

Decided to leave the ECU in the old air bag spot and parked the cam controller in the glove box.

 

805311D3-6E4E-4BE4-9D39-DCD67AE1C533.jpeg

 

This module is a bank of capacitors that keeps the dash/ecu powdered up when cycling the key while tuning.

 

D2CD861F-2538-423B-8C07-C0B63332C7C9.jpeg

 

 

Unless you look for it, you don’t see much of the Holley stuff under here. I can’t wait to be finished and replace this scuzzy carpet.

 

882BE066-4A37-4AC5-B786-B3A073E1522C.jpeg

 

The last input wire to land is for the HVAC and that’s the most important wire in the universe this time of year.

 

 

Moving along with the wiring. So far I’ve gotten the knock sensors connected and I’ve moved on to the IAC and TPS. This is switched power that remains constant during cranking.

 

CCB51AEF-69A0-4A15-8251-9909B5ADEF77.jpeg

 

All splices are soldered and covered with heat shrink. This was the constant power that goes to the distribution block on the battery.

 

F043B539-D488-4146-A3A9-992F5F1E1042.jpeg

 

Fuel pump relay and related wiring.

 

D76729C3-C307-483C-A610-4BD45E3DA4B7.jpeg

 

This is still a mess but I refuse to make any battery connections until I’m ready to start cycling power systems.

 

9541D38B-0BB6-457E-B8CA-E9F324AD2109.jpeg

 

Does anyone else sign their work area? I do. This is the route for the battery relocation wiring and the Holley power.

 

CE74EFFE-500B-4410-BC92-65D20E675BB7.jpeg

 

Holy CRAP... It goes into the body 

 

4687977B-E753-4190-8E68-A0FAE797F77F.jpeg

Link to post
Share on other sites

The knock sensor wiring was as simple as removing the sub-harness and connecting it to the HEFI harness.

 

EEE4825C-7F0E-4EAE-8764-A72FE15781D5.jpeg

 

The aforementioned IAC and TPS wiring will run underneath the intake and, once the connectors are swapped, will be a very clean install I think.

 

25CC4432-7AD6-47A8-B427-C34DE217B018.jpeg

 

Need to add four new wires to the J1B connector for the new IAC and then it’s just a matter of activating it in the software.

 

8AF76974-90B1-416A-BFD1-6B965CC7F3AC.jpeg

 

I’ve forgotten what a semi complete interior looks like. Can’t wait to be “finished building” so I can clean and paint the interior and body!

 

B6BAD6B1-5B9A-465A-A033-85A2D90B585B.jpeg

Link to post
Share on other sites

Small but meaningful progress today. Pulled this triple gauge panel out for @lwarrior1016 since he traded me the lower radiator hose I needed for it.

 

48B95EE9-FFE0-4AD1-9ED2-78AEEF04C251.jpeg

 

Found out this random connector I’ve held on to fits the TPS sensor in my new throttle body.

 

B8957560-698C-4947-AAD5-468AD47A6DE0.jpeg

 

Connected the Holley input wire for the HVAC controls and that’s about where I’ll stop today.

 

C39B2605-1FE6-4443-BF5C-E6A4424AD681.jpeg

 

This how the Holley will control my AC, for those interested:

 

E3743908-E289-4E7A-ADA9-D6C9B436D4DB.jpeg

 

Played hooky a few weeks back and decided to tackle some more wiring. I’ll address the IAC wiring first.

 

F7562842-7DC3-476B-9B9D-C9477D70059D.jpeg

 

 

Bought these gimmicky little shits last year to try out and they actually work pretty well.

 

D2E25D38-8467-438F-AFCF-DD241B518890.jpeg

 

Plus, I got to sit inside and work on it.

 

501C948D-1046-47CF-9593-58C13DE69F90.jpeg

 

As soon as the metri-pack pins arrive I’ll be able to finalize this harness.

 

01FB4892-A91A-4409-B858-9697ADD65F7E.jpeg

 

TPS wiring

 

2EF57DFB-E85E-4C35-911D-ABA1F4109C90.jpeg

4757CB7D-3EEE-4337-A462-7EF77769F3D2.jpeg

Link to post
Share on other sites

Here is an idea of what the wiring looks like installed. A few strategic ty-wraps to secure it, some wire loom on that phaser sensor wiring and it will look factory.

 

36511857-E41E-4103-BFE1-697BBACB95F7.jpeg

 

Here’s an idea of what the wiring looks like cleaned up a little 

 

B7FDBBD8-77C9-4626-A613-E6657064B437.jpeg

 

31976754-177F-437B-A90C-3D9B27D53982.jpeg

 

After the correct connectors finally arrived, I completed the new IAC circuit and installed the pins into the AMPSEAL connector. That is, after I figured out how the fuck to install said pins.

 

36D936C0-4855-4561-A80A-5ECF2EB0CB73.jpeg

 

Following the LS/LT diagram, I confirmed 46.7 ohms across one of the coils and installed the pins.

 

57C4728C-BD8C-480C-9D4E-E9605418341E.jpeg

 

 

Too easy!

 

B0BBCA8D-1379-4C12-BE9D-998209D5B7BF.jpeg

 

Like it was meant to be!

 

2FB70A68-7903-4003-9C0A-1DB4CD361098.jpeg

 

Finalized the cable route for the IAC but still haven’t addressed that stupid looking TPS. Hmm, I may just cut that boot off... Brb

 

39AB5DE9-7967-4478-8723-CA9D58280049.jpeg
 

 

 

Link to post
Share on other sites

Yup, I’ll say that worked well! So, I’ve RE-FINALIZED the IAC/TPS wiring and just need to pull the slack back under the intake.

 

53F013AB-197F-42C4-8AE6-52650E8A21C4.jpeg

 

AF363807-2222-4C6E-8DF0-649EAD8B7F45.jpeg

 

Swapped out the steering column bearing/seal ( thanks to @Akurma for the idea ) and holy crap was the original part in sad shape! Not only was it coming apart, the bearing was seized and missing pieces!

 

31498AD9-F476-4C14-ADB3-CCDEED58FAF0.jpeg

 

F3FAF743-5263-4DD0-BDC9-B85BAC672912.jpeg

 

C220BD18-D445-4817-B826-2F3CEE24B34D.jpeg

 

08177CE6-B602-45BA-8B2A-23916351BDF7.jpeg

Link to post
Share on other sites

Fuel line adaptor:

 

C85D9E03-FD43-4C06-A95F-F4CAF6DAABD3.jpeg

 

Coolant hose adaptor:

 

6ACC24A7-CB65-48A1-90AB-0660C1E969C9.jpeg

 

Put the rear on jack stands and started planning my new fuel line route.

 

CC5DCD33-78E6-4C07-9031-BC32639BEEBB.jpeg

 

I’m pretty sure I can do a better job than this hurried bullshit.

 

D374776C-C5DD-49E8-91B0-62E59D54E58A.jpeg

 

Now that I know NHRA rules forbid fuel lines in the driveshaft tunnel, I’ll be routing them along the subframe connector.

 

796CD6EA-580E-43D8-88BE-5E74CBC1F40A.jpeg

 

The challenge is going to be getting around the TA crossmember.

 

CB216495-C80D-426D-8B25-AB2BCDED6C58.jpeg

 

There will be 100% more T56 Magnum in this void very soon!

 

B65F523D-F6F6-40FA-A20C-1224968F3539.jpeg

Link to post
Share on other sites

Much better.

 

A7EFC6ED-82BD-4966-98A8-38FB9A21FA42.jpeg

 

CBA8DA06-5C1C-4A79-A795-68095AE94E78.jpeg

 

I’ll have to pull that tail pipe out to get the adel clamps above the axle but I’m not tremendously worried about it.

 

22C70304-ACF1-4B89-9B1E-76565709718D.jpeg

 

AF1ABD52-BCBD-4A71-AC69-B0208EB747B5.jpeg

 

1CA64629-E661-4821-B2AB-4877C9C7234C.jpeg

 

Small but meaningful progress after work yesterday, 8-3-20. Mounted the AFPR, extended the fuel pressure sensor wiring, secured the wiring under the frame rail and installed the AC accumulator.

 

9826620C-81DD-4CEF-8129-74F769264FF1.jpeg

 

A8189B88-CB62-4F17-BE0B-415FE1523B49.jpeg

 

068B59CC-B180-4ACD-9A9A-08E2C0C6029D.jpeg

 

After looking at this ^^^ again, I may try to route the wiring behind the accumulator.

 

BD46C156-B03B-4CF5-B426-3175C718A21C.jpeg

 

For my next trick, I’ll be connecting my fuel system in this manner:

 

2490754C-6BC0-4DED-8988-09D24A4E9A2B.jpeg

 

Took some time this evening to revamp my fuel lines for the 5ohh. I’m not sold on the line for the fuel rails but it’ll do for now. I need some more hose to make a long enough line.
 

83AC4AB0-7E0B-4265-953C-4C0376A592A6.jpeg

 

3E298290-5BF6-4ECB-AEE8-3A7358DC1E29.jpeg

 

 

 

 

 

 

7BB30A27-6B29-4CE1-AA89-22C059A9B2FD.jpeg

Link to post
Share on other sites
2 minutes ago, Evilcw311 said:

Feel like I already seen this somewhere before but can’t quite remember where.................


Sent from my iPhone using Tapatalk

 

Can you see the pictures on Tapatalk?

Link to post
Share on other sites

T56 Magnum


98F5D0E1-1B62-40C6-B1CF-22273C280D2C.jpeg

 

Fresh FoMoCo throw out bearing and adjustable pivot ball/stud:

 

56573F66-DD6A-46DE-BCF6-763973C4C76C.jpeg
 

What a pain in the ass!!

 

27D26777-4630-45DB-A582-9066DA6D982D.jpeg

 

16C820A7-AE26-46BA-B557-8E0F7585A83F.jpeg

Link to post
Share on other sites

What's left in order to make the maiden voyage:

  1. Swap driveshaft flange
  2. Square k-member
  3. install driveshaft
  4. fill transmission with fluid
  5. install shifter
  6. secure T56 crossmember/mount
  7. install exhaust
  8. adjust clutch cable
  9. reinstall front brakes
  10. stop rear 8.8 cover leak and top off fluid
  11. replace leaky, rear brake line
  12. bleed the brakes 
  13. Wheels/tires

Maybe a few things I’m forgetting? Such as some sort of cold air intake.

Link to post
Share on other sites

New driveshaft in!

 

4A09D740-F113-45A9-B992-35CD68A8C31F.jpeg

 

Shifter installed!

 

68B406AC-7706-4DC2-B69C-215A2B14D29F.jpeg

 

So beefy!
 

6FFDDB0C-F8BA-4193-87BE-2D341D7722D3.jpeg

 

New stainless steel brake lines installed! 
 

1DBBD532-E457-4338-8C6C-B62511B3A1F5.jpeg


This is actually the best fitting mid-pipe I’ve ever had and it even clears the torque arm!

 

FCCC13A3-90C8-4705-933A-EA43FB2A4A51.jpeg


Firewall adjuster installed!

 

D2BF5DE8-B741-452A-9927-9D97ACEC2494.jpeg

Link to post
Share on other sites
On 10/15/2020 at 11:24 PM, streetpilot said:

Anything new? I always look forward to seeing new progress in your thread.

Yes! I drove it! I have been neglecting this thread and I will now drop a massive update.

Link to post
Share on other sites

A little back story to reaching that milestone.

 

The car developed a tick and it progressed into a knock. Oh shit. Turns out the bolts for the passenger side cam phasers weren't torqued down and I came millimeters away from demise. Not good.

 

50519153638_d964670eb8_b.jpgProject Unicorn by oldawgnewtrikz, on Flickr

 

50520017557_ef1030a17a_4k.jpgProject Unicorn by oldawgnewtrikz, on Flickr

 

50520041282_4f1e7b7ade_4k.jpgProject Unicorn by oldawgnewtrikz, on Flickr

 

50519126238_b86f06cc0f_4k.jpgProject Unicorn by oldawgnewtrikz, on Flickr

 

I fought with the coolant system due to trapped air and a brand new, faulty thermostat. Wound up using a vacuum bleeder and a Ford thermostat with bypass holes drilled in it to get the soaring coolant temperature down. It would flash to 225* F rather quickly but now has settled around 178* F. My plan is to refresh the system with 50/50 coolant and a new thermostat now that I can trust it.

 

50519144618_99acfaca2b_4k.jpgProject Unicorn by oldawgnewtrikz, on Flickr

 

50520041332_a4259f4b31_4k.jpgProject Unicorn by oldawgnewtrikz, on Flickr

 

The hydroboost is disconnected since I have yet to install the Volvo power steering pump. This will happen sooner than later because I have NO brakes. It stops if you judo kick the pedal and that is the main thing stopping me from driving the car.

 

50520029052_05898a6e0b_4k.jpgProject Unicorn by oldawgnewtrikz, on Flickr

 

50520028812_9ee7ac292c_4k.jpgProject Unicorn by oldawgnewtrikz, on Flickr

 

Made the decision to put all of the original body panels on, including the vented hood, for a multitude of reasons. 

 

1. The fact I hadn't cut the Cobra hood for the Aerocatch latches yet. 

2. The laser red trunk didn't have a key and I was having trouble swapping the lock cylinders.

3. It's closer to one color this way. 

Link to post
Share on other sites

you have to be pretty happy with that sound I would imagine, or I would be.  I feel like I am a week or two behind you as I just sorted out the problem I was having with my turn signal inside and got to see them flash correctly.

Link to post
Share on other sites
39 minutes ago, ttocs said:

you have to be pretty happy with that sound I would imagine, or I would be.  I feel like I am a week or two behind you as I just sorted out the problem I was having with my turn signal inside and got to see them flash correctly.

I am very pleased with the exhaust note. It also made my truck sound like crap in comparison 😆

 

I haven’t kept this thread updated lately and need to fill in the blanks.

Link to post
Share on other sites
4 hours ago, streetpilot said:

Those pics are great. I always wondered what we were missing.


Next up is a front brake change to hopefully shift some of the bias to the front. I decided to install the used stuff while I sorted things out and the new brakes in the rear grab first.

Link to post
Share on other sites

More backdated build stuff! This installment shows me putting the headlights in, bolting that sexy T1 on and swapping to some matte black tail light bezels.

 

A3DA52B6-3781-4FCE-A7D8-460C3A82FDD8.jpeg

 

494D3C9B-AA3A-4A94-A154-562450C98664.jpeg

 

86A5E268-D1F6-46E2-B13B-6B7B68AD6E59.jpeg

 

CA243335-A6F7-4375-9DC5-6C3983371304.jpeg
 

A9B606A5-9ED6-4EF8-A034-516A4E51D3E1.jpeg

 

6AD670EE-5BE9-41BA-B9F7-3505E3C47EC8.jpeg

 

9FE56CF0-346D-4D31-B6D0-14C7388FF473.jpeg

 

889483F7-8A42-40A4-A9A3-AC5CA4073862.jpeg

 

10311E95-17D8-40ED-9A85-4CFCD593728F.jpeg

 

F26A7DD9-A70B-4276-BA49-918D7F62F745.jpeg

 


 

Link to post
Share on other sites

More backdated build stuff! 

The throttle cable needs to be adjusted because you essentially have to stomp it to make it move. That doesn’t help at all with a touchy twin-disc clutch that just chatters away unless you rev it. Gave bending the throttle cable bracket forward to lessen the angle of pull a try. The throttle is much smoother now.

The manual steering with a small Momo steering wheel also sucks major ass so I need to move forward with the Volvo electric power steering install.

The front brakes aren’t grabbing much at all even after several rounds of bleeding so more bleeding is in order. The rear brakes work, which meant I didn’t drive into that fence. Parked it and the e-brake cable snapped. Good times.

The FL500s oil filter interfered with the sway bar and I had to switch to a much shorter Wix filter to fit. I have a relocation and oil cooler installation in my future.

Overall, I’m genuinely stoked for this milestone. I have a tuning session for Tuesday and my buddy is loaning me his pneumatic brake bleed setup. I’m putting this bitch on the road one way or another.

Link to post
Share on other sites

More backdated build stuff! 
 

Cleaned the patio and garage up. It’s now time to put my feet up and relax.

2E38EDAF-52D9-4D97-9478-1294F4B2C532.jpeg

 

5D6E51B3-3FAF-41CA-B169-19A9283B0416.jpeg

New family portrait!

 

1D15EA58-6852-4ED6-9245-2BDACCA98A8D.jpeg

 

Oct 18th

 

Now featuring 100% more dome light, door chime and radio! I had taken those fuses out to preserve battery power when the car wasn’t running. 

 

B30E5ABC-DF89-42DA-9C89-325878A5E078.jpeg

 

BD06CD7B-585F-46AF-A0FA-83C33156D491.jpeg
 

The power windows and the door locks don’t work. A relay clicks in the trunk when you try the locks but I’ll save that for another day. These doors were from Space Ghost (my 98 GT that I totaled in 2016 for the newer crowd) and it was having some intermittent issues with that shit.

 

Oct 20


48F57369-8CFB-4815-887B-28ACD64B6C16.jpeg

 

Oct 25

 

Started on the power steering project today. Here is the step by step process:

Step 1: Jack the car up and secure it with a jack stand. Remove the tire. Decide against pulling the fender and bumper cover. Realize I need a hole saw and drive to Harbor Freight for some HIGH QUALITY TOOLS. 

6955632A-CD07-4E02-B5DE-6AE84F24E1A8.jpeg

Step 2: After the great Harbor Freight computer system fiasco of 2020, I stopped by O’reilly’s for some steering rack bellows. Finally returned home and proceeded to cut a large hole in my car.

261D1351-578C-400B-B5C1-310F27EA8F88.jpeg
 

Step 3: Mock the PS pump up to figure the brackets out. This was made easy by using the jack and taking careful measurements without using any measuring devices.


E2617096-21DF-4572-9384-D781E0B32906.jpeg

Why does this remind me of whack-a-mole?

Step 4: Start by drilling a few holes in the hastily constructed stainless steel forward bracket. Realize the battery in my DeWalt drill was low and swap it for the Craftsman drill. Furiously drilled into the stainless plate without a drop of lubricant until the shrill shriek of a suffering drill bit could be heard a block away. It was all going well until this battery died too. 

8E504E22-A0DD-46A4-8A78-9F5DB7EDA0E4.jpeg

Well. Shit. I’ll finish this tomorrow-ish.

 

Link to post
Share on other sites

More backdated build stuff!

 

Oct 26

 

Finished the installation of the pump using the factory mounting bracket from the Volvo. 

 

469786EA-6911-4D00-941A-C3A3360CF1CC.jpeg
 

7672A3BE-5F1E-452E-B045-20333390B2B5.jpeg

 

DCDC91BF-C886-49C4-92B4-0E9F43638527.jpeg

 

704B47CC-BAD4-4E78-9818-A28D497B1591.jpeg

 

AE1699BE-633B-4BD5-9B0E-079E79F33DE2.jpeg
 

Did a round of brake bleeding with the “Snap-On Ultimate power bleeder” ....

image.gif

....and I think it’s good enough. Now, I just need to finish the power steering system to see if they really work or not. 

44BA6A96-49F7-43D0-8145-14136DF5A9BA.jpeg

I didn’t get a picture of the canister in use so, use your imagination.

 

F0B2A263-C07B-4E41-8495-E66FE11CDDF6.jpeg

 


EF7F399A-C54C-4977-9700-9A520C5D0418.jpeg

 

9E6DEF9A-1977-4AC9-97F0-51788A61CEAA.jpeg

 

Link to post
Share on other sites

More backdated build stuff!


Oct 31

 

058D6298-50A5-4639-B194-4F3E6A558A90.jpeg

 

548DF2D3-E108-467D-BB92-9ECD037260C3.jpeg

 

D5AA968D-E139-4508-9324-BE73DD307DE0.jpeg


This is when I realized I had the incorrect high pressure fitting.

 

20006B77-42E1-409C-A537-5FB03307F987.jpeg

 

157B756E-9728-46B0-9C0E-2D3DBCC35F18.jpeg
 

D0073E3D-0AD9-4075-BEE8-302F25072297.jpeg

 

EE1DED95-4D61-4E36-890C-9DC442175A1E.jpeg

 

9040B2F2-06F0-4BD0-A980-40B0C4338B73.jpeg

 

This is the correct fitting.

 

028C0642-1238-4EB7-917D-B075E106BB10.jpeg

1A2DB477-FE9B-499D-A34C-7B78F032FA67.jpeg

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


SN95 Source ©

The premier SN95 Community

×
×
  • Create New...